|
Carbo Tech, Inc.
| Veteran Owned
Small Business Corporation |
PH: 770-267-8821 FAX:
770-267-7286 |
|
|
Used 7.5 ton (mailbox
style) CO2 receivers Price
to include - fill space between outer jacket and inner pressure vessel with urethane
insulation, paint exterior, new R-404A refrigeration unit with new
electrical controls for automatic operation, new single bleeder, new dual ASME safeties, new Jamesbury stainless steel ball valves on one each vapor
balance and liquid fill lines (w/CGA fittings and hose blow-down valves),
and vapor and liquid process lines and three instrument isolation valves,
existing liquid level indicator, new pressure indicator and complete check
out with all controls set for proper operation. Cardox mailbox design
w/363 psi maximum allowable working pressure
NB#43207 Vessel data report available upon request
|
|
|
Used 12 ton CO2 Receiver Includes: Cover original insulation system with
aluminum sheets on sides, repaint heads and supports as needed, new
evaporator coil, install new Copeland R-404A refrigeration unit with new
LCR style electrical controls for automatic operation, new single bleeder,
new dual Kunkle ASME safeties (sized for outdoor installation), new
Jamesbury stainless steel ball valves on one each vapor balance and liquid
fill lines (w/CGA fittings and hose blow-down valves), and vapor and
liquid process lines and three instrument isolation valves, rebuild
existing liquid level indicator, new pressure indicator, recover existing
control cabinet with pre-painted white aluminum sheet with new hardware
and complete check out with all controls set for proper operation.
NB #8531 Vessel data report available upon
request Skid mounted with standard cabinet and lockable access door
|
|
|
12 ton capacity Liquid Carbonic style CO2 receiver Includes: Cover original insulation system with
aluminum sheets on sides, repaint heads and leg supports as needed, new
oak insulators under tank supports with new hardware, install new Copeland
R-404A refrigeration unit with new LCR style electrical controls for
automatic operation, new single bleeder, new or rebuilt ASME safeties
(sized for outdoor installation), new Jamesbury stainless steel ball
valves one each vapor balance and liquid fill lines (w/CGA fittings and
hose blow down valves), and vapor and liquid process lines and three
instrument isolation valves, rebuild existing liquid level indicator, new
pressure indicator, recover control cabinet with prepainted white aluminum
sheet with new hardware and complete checkout with all controls set for
proper operation.
NB #32279 Vessel data report available upon
request Skid mounted economy style with sheet metal cover over the
refrigeration unit |
|
|
|
Refurbished 14 ton
Tomco "C" CO2 Receivers Priced to include - Remove
aluminum sheets off sides, repair the insulation as needed, recover
with pre-painted aluminum sheets, repainr heads and saddle supports
as needed, replace oak insulators under tank supports if needed
using new hardware, install new 2HP Copeland R-404A refrigeration
system, new Cutler Hammer electrical controls with fused disconnect,
motor starter, Allen Bradley pressure switch, control voltage relay
and all other controls necessary for automatic operation, new dual
bleeders, new or rebuilt dual ASME safeties (sized for outdoor
installation), new Jamesbury Eliminator stainless steel ball valves
on one each vapor balance and liquid fill lines (w/CGA fittings and
hose blow-down valves), and vapor and liquid process lines and three
instrument isolation valves, rebuild existing Barton liquid level
indicator, new pressure indicator, recover control cabinet with
pre-painted white aluminum sheet with new hardware and complete
check out with all controls set for proper operation.
NB #169
Vessel data report available upon request
NB #11834 Vessel data report available upon request
|
|
|
Refurbished 26 ton CO2 Receiver Priced to include: remove
aluminum sheets off sides, repair the insulation as needed,
recover with pre-painted aluminum sheets, repaint heads and saddle
supports as needed, install new 3 HP Copeland R-404A refrigeration
system. new Cutler Hammer electrical controls with fused disconnect,
motor starter, Allen Bradley pressure switch, control voltage relay
and all other controls necessary for automatic operation, new dual
bleeders, new or rebuilt dual ASME safeties (sized for outdoor
installation), new Jamesbury Eliminator stainless steel ball valves
on one each vapor balance and liquid fill lines (w/CGA fittings and
hose blow-down valves), and vapor and liquid process lines and three
instrument isolation valves, rebuild existing Barton liquid level
indicator, new pressure indicator, recover control cabinet with
pre-painted white aluminum sheet with new hardware and complete
check out with all controls set for proper operation
NB
#2286 Vessel data report available upon request
|
|
|
Refurbished 26 ton Taylor Wharton CO2 Receiver -
Includes: remove aluminum sheets off sides, repair the insulation as
needed, recover with pre-painted aluminum sheets, repaint heads and
saddle supports as needed, replace oak insulators under tank
supports if needed using new hardware, install new 3 HP Copeland
R-404A refrigeration system. new Cutler Hammer electrical controls
with fused disconnect, motor starter, Allen Bradley pressure switch,
control voltage relay and all other controls necessary for automatic
operation, new dual bleeders, new or rebuilt dual ASME safeties
(sized for outdoor installation), new Jamesbury Eliminator stainless
steel ball valves on one each vapor balance and liquid fill lines
(w/CGA fittings and hose blow-down valves), and vapor and liquid
process lines and three instrument isolation valves, rebuild
existing Barton liquid level indicator, new pressure indicator and
complete check out with all controls set for proper operation.
NB
#236 Vessel data report available upon request
|
|
|
Refurbished 26 ton Vertical CO2 Receiver - Includes: strip to
bare pressure vessel, prime vessel and supports, reinsulated using
4” urethane insulation covered with .063” pre-painted white aluminum
sheets, painted white aluminum top head, fabricated flat bottom head
covered with pre-painted white aluminum, new Copeland 3 HP R-404A
refrigeration system, new Cutler Hammer control panel with fused
disconnect, motor starter, Allen Bradley pressure switch, control
voltage transformer and all other controls necessary for automatic
operation, dual bleeders, new or rebuilt dual ASME safeties (sized
for outdoor installation), new Jamesbury stainless steel ball valves
on one each vapor balance and liquid fill lines (w/CGA fittings and
hose blow-down valves), and vapor and liquid process lines and three
instrument isolation valves, rebuild existing liquid level
indicator, new pressure indicator and complete check out with all
controls set for proper operation.
NB #684
Vessel data report available upon request
|
|
|
Refurbished 30 ton Tomco Vertical CO2 Receiver- Includes:
Remove aluminum sheets off sides, repair the insulation as needed,
recover with pre-painted aluminum sheets, repaint heads and saddle
supports as needed, replace oak insulators under tank supports if
needed using new hardware, install new 3 HP Copeland R-404A
refrigeration system. new Cutler Hammer electrical controls with
fused disconnect, motor starter, Allen Bradley pressure switch,
control voltage relay and all other controls necessary for automatic
operation, new dual bleeders, new or rebuilt dual ASME safeties
(sized for outdoor installation), new Jamesbury Eliminator stainless
steel ball valves on one each vapor balance and liquid fill lines
(w/CGA fittings and hose blow-down valves), and vapor and liquid
process lines and three instrument isolation valves, rebuild
existing Barton liquid level indicator, new pressure indicator,
recover control cabinet with pre-painted white aluminum sheet with
new hardware and complete check out with all controls set for proper
operation
NB: 1734 and 1736
Vessel data reports available upon request
|
|
|
Refurbished 50 ton horizontal CO2 receivers
-Amerigas
design horizontal CO2 receiver priced to include:
Remove aluminum sheets
off sides, repair the insulation as needed, recover with pre-painted
aluminum sheets, repaint heads and leg supports as needed, install
new 6 HP Copeland R-404A refrigeration system. new Cutler Hammer
electrical controls with fused disconnect, motor starter, Allen
Bradley pressure switch, control voltage relay and all other
controls necessary for automatic operation, new dual bleeders, new
or rebuilt dual ASME safeties (sized for outdoor installation), new
Jamesbury Eliminator stainless steel ball valves on one each vapor
balance and liquid fill lines (w/CGA fittings and hose blow-down
valves), and vapor and liquid process lines and three instrument
isolation valves, rebuild existing Barton liquid level indicator,
new pressure indicator and complete check out with all controls set
for proper operation.
National board #177
National board #189
Vessel data reports available upon request
|
PLEASE NOTE: Pictures show basic style of
receivers offered. Actual receivers may vary slightly in appearance.
All receivers tested before shipment with all controls set for proper
operation. Vaporizers not included unless noted, but are available.
Used equipment list changes often so please call or e-mail us for an
updated listing.
Static Receivers
Home Page
sales@carbotech.com
info@carbotech.com
tech@carbotech.com
|
